Tab Content
  • Tom's Avatar
    09-15-2020, 08:38 AM
    Tom replied to a thread Time to ride in The Ride
    Hell ya ..... :)
    12 replies | 190 view(s)
  • Tom's Avatar
    09-10-2020, 05:40 PM
    Tom replied to a thread Time to ride in The Ride
    I read if u make over 47 k feds only tax u 1 dollar for every 3 over .., less than that 1 for every 2 over ,, little guy gets it again :(
    12 replies | 190 view(s)
  • dawg's Avatar
    09-10-2020, 12:31 PM
    dawg replied to a thread Time to ride in The Ride
    Tom, it is my understanding that those same 14 states that don’t tax pensions don’t tax social security either. Of course you will still have to pay...
    12 replies | 190 view(s)
  • Tom's Avatar
    09-10-2020, 09:18 AM
    Tom replied to a thread Time to ride in The Ride
    Boy I’ve got a lot to learn I retire in December know I continue to work I don’t have any pension but I figured I better make sure there’s money in...
    12 replies | 190 view(s)
  • dawg's Avatar
    09-09-2020, 07:09 PM
    dawg replied to a thread Time to ride in The Ride
    Any experience with Cleveland, TN? That looks to be east coast down by Georgia. TN is one of the 14 states that won’t tax my pension.
    12 replies | 190 view(s)
  • Tom's Avatar
    09-09-2020, 08:38 AM
    Tom replied to a thread Time to ride in The Ride
    It is cooled off here too. Being that I’m only working part time the neighbor gave me her old bicycle so I’ve been riding around North end south...
    12 replies | 190 view(s)
  • dawg's Avatar
    09-08-2020, 05:08 PM
    dawg replied to a thread Time to ride in The Ride
    Enjoy the ride....and scope out a town in Tennessee for me to retire to in 6 years. I’m thinking east coast and down near the Georgia line for the...
    12 replies | 190 view(s)
  • Tom's Avatar
    09-03-2020, 09:02 AM
    When either the regulator or the stator goes out. I try to change them both at the same time but that’s up to the person doing the job, glad to see...
    7 replies | 178 view(s)
  • Tom's Avatar
    08-26-2020, 09:07 AM
    That’s also a good place if you have to get a flat tire the dealership. You are so lucky the dealership in your area will work on an older bikes ,,...
    7 replies | 178 view(s)
No More Results

31 Visitor Messages

  1. View Conversation
    Thank you again .. Sir ,,
  2. View Conversation
    Hello I see quite a few windshields for heritage and or fat boys from 2000 and up I can’t seem to find out if they would work for my 98 was there some change in dimensions or something that would really say I can’t use it thank you for all your great info have a great day Tom
  3. View Conversation
    Thank you for the information ..
    Very appreciative ....,
  4. View Conversation
    Me again
    Odometer black out ;(
    The odometer is All with little black dots so you can’t really read it Speedo works and this seems to be a problem and 98 99 mines in 98. A friend has an 06 speedo it’s plug and play ..mine has several wires with eyelets. Is there any suggestion or does anyone know of a way to adapt the 06 to 1998 or just keep looking for a good used Speedo ,which seems to be like looking for hens teeth .....thanks
  5. View Conversation
    Then again it’s always something I change the fork oil while it was up on the jackstand and now the right-hand leg I come out after work there’s a puddle a fork oriole it ran down the leg down the caliper around the rotor and under the tire thank goodness there is two brakes on the front tire. Always something guess I better rebuild that leg with some new seals
  6. View Conversation
    Again thank you for your help your help bikes back on the road good too because it’s 80
  7. View Conversation
    Thank you for your help
  8. View Conversation
    Here is mine I know they have been upgraded a few times I was able to get one off of eBay it’s an 08 designation mine was an 08 a designation I was wondering course it’s late now I already bought it if I would get a new one at the dealer would it be one that has the longer numerical designation as part seem to do now I will post a video of what mine sounded like and I do have a picture on the thread that I posted , Of the broken tooth I’m just hoping it is a plastic tooth problem not something the computer made the little motor do that broke it Tx
  9. View Conversation
    I recently started a thread my induction module started chattering I ordered a used one one is there any trick to or a good way or something special about installing the induction module. To a tooth broke off the large gear inside the one that is work or connected to the shaft to the butterfly in the Venturi. One I was wondering if you ever seen this happen Into do you think it just happened because of the plastic tooth breaking off or could it be a signal from the computer that caused it to go the wrong direction when I first turn the ignition on have you ever heard of this thank you very much for your help Tom
Showing Visitor Messages 1 to 10 of 31
Page 1 of 4 1234 LastLast
Page 1 of 4 1234 LastLast
About dawg

Basic Information

Date of Birth
November 2
About dawg
2019 FLTRU


I blame soos


Total Posts
Total Posts
Posts Per Day
Visitor Messages
Total Messages
Most Recent Message
07-12-2018 07:26 AM
General Information
Last Activity
Yesterday 05:47 PM
Join Date
Home Page

7 Friends

  1. Bagger Bagger is offline

    Road Warrior

  2. clutchglass clutchglass is offline

    Moderator / Sergeant at Arms

  3. Hobbit Hobbit is offline


  4. mat60 mat60 is offline

    Ride Captain

  5. soos soos is offline

    Site Sponsor

  6. Tom Tom is offline

    New Member Liaison

  7. UC Wayne UC Wayne is offline


    UC Wayne
Showing Friends 1 to 7 of 7

HarleyTalking.com is a privately owned internet discussion forum and is not affiliated with, endorsed by, or sponsored by Harley Davidson, Inc in any way. The Harley Davidson names and logos are trademarks owned by Harley-Davidson, Inc.