HarleyTalking

Search:

Type: Posts; User: dawg

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    18
    Views
    306

    Every 5k or once a year. That said, if I had only...

    Every 5k or once a year. That said, if I had only 1k miles on it, I would not change it.
  2. Replies
    7
    Views
    156

    Sometimes bearings just go, especially the cheap...

    Sometimes bearings just go, especially the cheap junk. When washing, don’t spray directly at the bearing, specifically if it’s power washing.
  3. Replies
    9
    Views
    430

    Me too, or if had an extra 10k to part with and...

    Me too, or if had an extra 10k to part with and keep both
  4. On a 2000 I’d be surprised to see excessive crank...

    On a 2000 I’d be surprised to see excessive crank runout. They had the good forged cranks and good left bearing back then. 2002 was the last year of those. There have been a few scored SE plates and...
  5. Thread: high oil pressure

    by dawg
    Replies
    2
    Views
    125

    I now get that pressure on my 08 ultra because I...

    I now get that pressure on my 08 ultra because I put in the Axtell bypass. Prior it was about 35 rolling and about 5 at a stop
  6. Replies
    81
    Views
    2,434

    Looks like a great trip....if I could only take...

    Looks like a great trip....if I could only take 30 straight days off from work
  7. Replies
    115
    Views
    4,292

    Looks great

    Looks great
  8. Thread: Leg change

    by dawg
    Replies
    2
    Views
    1,271

    You talking about the reducer kits to use a 3/4”...

    You talking about the reducer kits to use a 3/4” axle in a 1” bearing?...
  9. Thread: New Bike today!!

    by dawg
    Replies
    43
    Views
    2,182

    Great looking bike, but I wouldn’t let that ugly...

    Great looking bike, but I wouldn’t let that ugly sumabitch that photobombed your pic anywhere near the bike

    :BigBouncingSmilie:
  10. Replies
    12
    Views
    1,180

    Should stop by Duluth Trading Post and pick up...

    Should stop by Duluth Trading Post and pick up some of them “ballroom jeans” to let the boys breathe.....or the Kevlar crotch ones that are good for fighting off angry beavers!!!
  11. Replies
    14
    Views
    1,414

    I believe the OP understands that the pressure...

    I believe the OP understands that the pressure drop at idle is normal, which occurs on his 05 road glide. I think his question is, that being normal, why does his 05 Electra stay steady at 32 and not...
  12. Replies
    5
    Views
    985

    They actually work well according to many I’ve...

    They actually work well according to many I’ve seen mention them.
  13. Replies
    14
    Views
    1,414

    Are you the original owner of the 05 Electra?...

    Are you the original owner of the 05 Electra? Perhaps a shim or Baisley spring was put in the oil relief valve? It’s normal what your 05 roadglide is doing, and that’s what your 05 Electra would be...
  14. I’ve seen many a wiring issue in the older...

    I’ve seen many a wiring issue in the older batwing fairing bikes where the wires get chafed due to crossing over the fairing brackets. I agree with Bob that it’s probably a grounding issue due to a...
  15. Replies
    15
    Views
    826

    Welcome from VT. Nice bike. I have a brother in...

    Welcome from VT. Nice bike. I have a brother in Dacula
  16. Thread: New handlebars

    by dawg
    Replies
    11
    Views
    512

    Welcome from VT, Bob has the right advice (I...

    Welcome from VT, Bob has the right advice (I suppose I should say “Bob’s your uncle” now).
  17. Replies
    13
    Views
    481

    He’s using a 6 gallon tank. The 1311D sealing...

    He’s using a 6 gallon tank. The 1311D sealing screws and top gasket aren’t used on the 08 and later touring tanks.
  18. Replies
    13
    Views
    481

    You can see the parts in the 6 gallon tanks in...

    You can see the parts in the 6 gallon tanks in the pic. #18 is the top plate of which I speak.

    22645
  19. Replies
    13
    Views
    481

    Top plate is separate from the fuel pump. Anyone...

    Top plate is separate from the fuel pump. Anyone needing a new pump would keep their top plate and just replace the pump.
  20. Replies
    13
    Views
    481

    Would just need the top plate to put in the hole....

    Would just need the top plate to put in the hole. Look at a parts fiche to see. It’ll swap over with some slight modifications.
  21. Thread: New from PA

    by dawg
    Replies
    17
    Views
    915

    Welcome from VT...post up a pic of your ride, we...

    Welcome from VT...post up a pic of your ride, we like pics
  22. He looks a little bit like Hoggle from the movie...

    He looks a little bit like Hoggle from the movie Labyrinth :FingerOpenMouth:
  23. Replies
    17
    Views
    1,503

    Nice. I like the looks of the 2018 Jade over...

    Nice. I like the looks of the 2018 Jade over Black Springfield (especially with an added tour pak)
  24. Welcome from VT. Smitty makes a good point....

    Welcome from VT. Smitty makes a good point. Living in VT, I took off my aftermarket oil cooler I had installed because it was more trouble than it was worth. It doesn’t get real hot up here. I...
  25. Thread: Had to ride

    by dawg
    Replies
    10
    Views
    736

    Good luck with the doc, hope all is well and...

    Good luck with the doc, hope all is well and there is nothing serious with the blood tests
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

HarleyTalking.com is a privately owned internet discussion forum and is not affiliated with, endorsed by, or sponsored by Harley Davidson, Inc in any way. The Harley Davidson names and logos are trademarks owned by Harley-Davidson, Inc.